Enterasys-networks XSR-3150 Manuel d'utilisateur télécharger pdf (Page 103)

Cable, CompactFlash and Accessory Specifications

XSR Getting Started Guide A-17

Installing Shunt/Terminal Strip

To install the shunt or terminal strip, attach two dual-pin units vertically to P1 and P2 four-pin

jumpers corresponding to the RJ-45 port using a balun, as shown in Figure A-20. Any other RJ-45

ports on the NIM card connected to 120-ohm lines do not require shunts.

Figure A-20 Installing a Termination Shunt on BRI-S/T NIM Card

P2P1

Port 0 Port 1

F14

F16

CR1

F17

J1 J2

Receive Pair Termination

Transmit Pair Termination

Port 0 Port 1

CR2

R132

R133

F15

F1 F2 F3 F4 F5 F6 F7 F8

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 109 110

X-Pedition 1
Security Router 1
Industry Canada Notices 5
Class A ITE Notice 5
Clase A. Aviso de ITE 5
Klasse A ITE Anmerkung 5
orcontact 6
(Circuit Modules) 7
(Circuit Breakers) 7
VCCI Notice 8
BSMI EMC Statement — Taiwan 8
Declaration of Conformity 8
Australian Telecom 9
Contents 13
Appendix A: Specifications 15
About This Guide 17
Getting Help 19
Overview 21
XSR-3150 22
System Description 23
XSR Getting Started Guide 1-3 23
Operating System 24
Industry-common CLI 24
IP Protocol 24
IP Routing 25
SNMP and Statistics Gathering 25
Security 26
Frame Relay 26
XSR Getting Started Guide 1-7 27
Quality of Service (QoS) 28
Virtual Private Network (VPN) 28
GRE over IPSec 29
Dial Service 30
Dial Backup 30
Installation Overview 31
1-12 Overview 32
Hardware Installation 33
2-2 Hardware Installation 34
XSR Getting Started Guide 2-3 35
2-4 Hardware Installation 36
ETH3ETH2ETH1 37
2-6 Hardware Installation 38
Connecting Cables 39
2-8 Hardware Installation 40
XSR Getting Started Guide 2-9 41
Figure 2-16 42
Figure 2-18, respectively 43
Software Configuration 45
Initializing XSR Software 46
3-2 Software Configuration 46
XSR Getting Started Guide 3-3 47
Setting the Clock 51
Configuring the LAN Ports 52
Configuring the WAN Ports 52
BRI Leased Line 53
BRI Leased Frame Relay 54
BRI Switched Line 54
Firewall Sample Configuration 56
Internal 57
Setting Up RIP Routing 58
Configure OSPF Routing 59
3-16 Software Configuration 60
Viewing Your Configuration 62
Site regional router 64
Configure Users and Passwords 66
Configure LAN Interface 66
Configure Quality of Service 66
Apply QoS 68
Configure More Access Lists 69
Configure DHCP/BOOTP Relay 69
Configure SNMP 70
XSR-1850 71
Set Up IKE Phase I Security 72
Create a Transform Set 72
Configure Crypto Maps 72
3-32 Software Configuration 76
XSR Rebooting Characteristics 77
Power-Up Reboot 78
Table 1 Reboot Triggers 78
Bootrom Monitor Mode Commands 79
3-36 Software Configuration 80
3-38 Software Configuration 82
3-40 Software Configuration 84
3-42 Software Configuration 86
Specifications 87
PC/uplink port 88
Short-haul MTRJ 89
Pin 1 Pin 5 90
Pin 6 Pin 9 90
Pins not shown are unused 96
RX In TX Out 99
G.703 Balun 99
Model 460 MC 99
NIM-E1-CO 99
Regulatory/Safety Compliance 101
ALARM LOS 101
ENABLE LOF 101
Port 0 Activation LED 102
Port 1 Activation LED 102
Pin 8Pin 1 102
Receive Pair Termination 103
Transmit Pair Termination 103
Port 0 Port 1 103
NIM1 NIM2 107
LED State Function 108
Index-2 110

Commentaires sur ces manuels

Pas de commentaire

Enterasys-networks XSR-3150 Manuel d'utilisateur Page 103

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Enterasys-networks XSR-3150