Enterasys Networks G3G124-24 Manuel d'utilisateur Page 41

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 59
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 40
Connecting to the Network
Enterasys G-Series Hardware Installation Guide 2-19
Removing an XFP/SFP
Toremoveatransceiverfroma portslot,referbacktoFigure 210andproceedasfollows:
1. Withanantistaticwriststrapattachedtoyourwrist,removethecablesconnectedtothe
transceiver.
2. Releasethetransceiverusingitswirehandle.Specificoperationandlocationofthehandle
willvarydependingontransceiver
type.
3. Graspthesidesofthetransceiverandpullitstraightout oftheportslot.
IfstoringorshippinganXFP/SFP,whichhasafiberopticconnector,insertitsprotectivedust
covertoprotecttheendsofthefiberopticfibersfromdustorcontamination.
Connecting Fiber-Optic Cables to SFP/XFP Ports
BeforeconnectingcablestoSFP/XFPports,youmustinstalltheappropriatetransceiveras
describedinInstallingOptionalSFP/XFPonpage 217.Thissectiondescribeshowtoconnecta1‐
or10GigabitfiberopticsegmentfromthenetworkorotherdevicestoanSFPorXFPLCport
connector(LCor
MTRJ).
EachfiberopticlinkconsistsoftwofiberopticstrandswithinthecableforTransmit(TX)and
Receive(RX).Thetransmitstrandfromadeviceportconnectstothereceiveportofafiberoptic1
/10‐GigabitEthernetdeviceattheotherendofthesegment.Thereceive
strandoftheapplicable
LCorMTRJportconnectstothetransmitportofthefiberoptic1/10‐GigabitEthernetdevice.
RefertoFigure 211asyouperformthefollow ingprocedure.
ToconnectanLCorMTRJcableconnectortoanSFPorXFPportconnector:
1. Removetheprotective
covers(notshown)fromtheuplinkportSFP/XFPandfromthe
connectorsoneachendofthecable.
Caution: Do NOT remove the XFP/SFP from the port slot without releasing it. The XFP/SFP is
released by pulling down on its wire handle. Attempting to remove the XFP/SFP without releasing it
can damage the XFP/SFP.
The XFP/SFP and its host G-Series are sensitive to static discharges. Use an antistatic wrist strap
and observe all static precautions during this procedure. Failure to do so could result in damaging
the XFP/SFP or host G-Series. Always leave the XFP/SFP in the antistatic bag or an equivalent
antistatic container when not installed.
Precaución: NO quite el XFP/SFP de la ranura sin antes abrir la traba ubicada en la parte frontal
del XFP/SFP. Si lo hace, puede dañar el XFP/SFP, puesto que es muy sensible a las descargas de
electricidad estática, al igual que el dispositivo host. Utilice la pulsera antiestática y tome todas las
precauciones necesarias durante este procedimiento. Si no lo hace, pude dañar el XFP/SFP o el
dispositivo host. Mientras no esté instalado, mantenga el XFP/SFPen su bolsa antiestática o en
cualquier otro recipiente antiestático.
Caution: Do not touch the ends of the fiber-optic strands, and do not let the ends come in contact
with dust, dirt, or other contaminants. Contamination of cable ends causes problems in data
transmissions. If the ends of the fiber-optic strands become contaminated, use a canned duster to
blow the surfaces clean. A fiber-port cleaning swab saturated with optical-grade isopropyl alcohol
may also be used to clean the ends.
Precaución: No toque los extremos de los cables de fibra óptica y evite su contacto con el polvo,
la suciedad o con cualquier otro contaminante. Si los extremos de los cables se ensucian, es
posible que la transmisión de datos se vea afectada. Si nota que losextremos de los cables de
fibra óptica se ensucian, utilice aire comprimido paralimpiarlos. También puede limpiarlos con un
estropajo embebido en alcohol isopropílico.
Vue de la page 40
1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 58 59

Commentaires sur ces manuels

Pas de commentaire